Honeywell VR4605C1136 gas valve

Honeywell VR4605C1136B regulators are designed to control gas flow in domestic heating systems, water heaters and boilers. They perform standard functions and can be supplemented with pressure regulators, throttle valves, devices for smooth ignition, two-level regulation and gas flow control.

The Resideo VR4605C 1136B Compact Automatic gas valves can operate from mains or low-voltage power supply and have different throughput. They are suitable for working with various types of gases, including MFD Group A (G110), MFD group B (G 120), natural gas H (G 20), natural gas L (G25) and liquefied gas LP (G30).

These gas regulators are equipped with two electrical actuators: one for opening a safety valve of class A or B according to EN 161 and the other for opening the main valve of class B, C or J according to EN 161.

The valve gas Hanivel VR4605 C 1136B is suitable for boilers BAXI SLIM HPS 1.80 and boilers SIME RX 37-48-55 kW, RMG Mk.II 70-80 kW, Bitherm OF 37-80 kW: 6089702, 711552100.

General characteristics

• Inlet and outlet are suitable for flanged connection

• Screen on the input side

• Pressure valve on the input and output sides

• Gas connection inlet: diameter 18.6mm, outlet: 1/2″ BSP.Pl

• Compression fitting –

• Back pressure of the 1st valve: 50 mbar; 2nd valve: –

• Ambient temperature 0…60°C

• Maximum inlet pressure 60 mbar

• CE compliance yes

Notes

• Switchable softlight (in combination with adapter assembly)

• Coil with top connection

Management functions

• Maximum operating pressure 45 mbar

• Pilot flow –

• Leakage requirements according to EN 126

• Capacity (by air) 3.1 m3/h with a pressure drop of 3 mbar

• Softlite pressure 5 mbar -3/-0.5 after 1.5 s

• Operator V404A 1329 (45.801.130-001)

Standard conditions

• Flow indication, m3/h

• Registration of the output pressure using a sensor connected to a half-inch pipe, the length of which is 10 times the diameter, by means of a short hose with a length equal to 5 diameters

• Rated voltage

• Vertical position, i.e. the position when the actuators are on top

• Nominal pressure 25 mbar, dry air at 20 °C

• Ambient pressure = 1013 mbar

• Ambient temperature = 20 °C

• 2.8mm output aperture

General provisions

The Hanivel VR4605C1136U gas solenoid valve is designed for use with gas heating systems that support DSI, HSI or IP ignition for the main burner. The main burner is controlled by two-position electrical actuators.

The valve includes an internal fine mesh filter on the inlet side and can be equipped with an outlet mesh filter on request. Various models with different closing strength are available: B+ B, B + J, B+C, A+ J and A+C.

To control and adjust the pressure of the burner, there are pressure measuring fittings with an outer diameter of 9 mm on the input and output sides. The regulator can be installed within an angle of 90° in any direction from the vertical position of the two-position electric actuator.

The base of the VR4605C 1136U gas valve has two threaded mounting holes for mounting on the heating system. The two-position actuator of the tracking type of the main valve is equipped with an electrical connector according to DIN standard and can be connected to AMP connectors.

The principle of operation

The VR4605 C 1136U regulator automatically controls the gas outlet pressure. Its principle of operation is to use a built-in positive feedback system that ensures reliable closure of the main valve in the event of a power failure or gas supply.

This system guarantees a stable outlet pressure, regardless of changes in the inlet pressure. If a small volume of gas is disconnected from the regulator, the outlet pressure is adjusted to compensate for the pressure difference.