Honeywell VR4605A1039 gas valve

Honeywell VR4605 A 1039B gas solenoid valves are designed for safe gas flow control in domestic heating systems, heaters, boilers and water heaters. They provide standard functions and can be supplemented with various options, such as a pressure regulator, a throttle valve, a smooth ignition device, two-level regulation and modulation of gas flow. Hanivel VR4605A 1039B Compact Automatic gas valves are available with different power options, including mains and low-voltage, as well as different capacity.

Each of these regulators includes two electrical actuators:

– One for controlling the opening of the safety valve of class A or B according to EN 161.

– The other for controlling the opening of the main valve of class B, C or J according to EN 161.

These regulators are suitable for use with various types of gases, including petroleum gases MFD group A (G110), MFD group B (G 120), natural gas H (G 20), natural gas L (G25) and liquefied gas LP (G30).

General characteristics

1. The inlet and outlet are suitable for flanged connection

2. Screen on the input side

3. Pressure valve on the inlet and outlet sides

4. Gas connection inlet: 1/2″ BSP.Pl Outlet hole: 1/2″BSP.Pl

5. Compression fitting –

6. Back pressure of the 1st valve: 50 mbar of the 2nd valve: –

7. Ambient temperature 0…60°C

8. Maximum inlet pressure 60 mbar

9. CE compliance yes

Management functions

1. Maximum operating pressure 45 mbar

2. Pilot flow –

3. Leakage requirements according to EN 126

4. Capacity (by air) 3.1 m3/h with a pressure drop of 3 mbar

5. Softlite Pressure –

Standard conditions

• 2.8mm output aperture

• Flow indication, m3/h

• Nominal pressure 25 mbar, dry air at 20 °C

• Ambient pressure = 1013 mbar

• Ambient temperature = 20 °C

• Registration of the output pressure using a sensor connected to a half-inch pipe, the length of which is 10 times the diameter, by means of a short hose with a length equal to 5 diameters

• Rated voltage

• Vertical position, i.e. the position when the actuators are on top

General provisions

The Resideo VR4605A1039B gas regulator is designed for gas heating installations with DSI, HSI or IP ignition systems for the main burner.

The main burner is controlled by two-position electrical actuators.

The VR4605 A 1039U controller includes an internal fine-mesh filter on the input side, and can be equipped with an output mesh filter on request. Different models with different closing strength are available:

1. B + B
2. B + J
3. B + C
4. A + J
5. A + C

To control and adjust the pressure of the burner, there are pressure measuring fittings with an outer diameter of 9 mm on the input and output sides. The regulator can be installed within an angle of 90° in any direction from the vertical position of the two-position electric actuator.

At the base of the VR4605A 1039U valve, two threaded mounting holes are provided for mounting on the heating system. The two-position actuator of the tracking type of the main valve is equipped with an electrical connector according to DIN standard and can be connected to AMP connectors.

Principle of operation

The VR4605A1039U gas solenoid valve provides automatic control of the gas outlet pressure. It has a built-in positive feedback system, which guarantees the closure of the main valve in case of a power failure or gas supply.

This system ensures a stable outlet pressure, regardless of changes in the inlet pressure. When small volumes of gas are disconnected from the regulator, the outlet pressure is adjusted to compensate for the pressure difference.

If pressure regulation is not required, the regulator spring can be locked. In this case, the full pressure of the “servogas” determines the position of the main valve, which allows you to control the output pressure.